manualshive.com logo in svg

Lissmac MAB 2001, Operating Instructions Manual

Share
Download
Lissmac MAB 2001 Operating Instructions Manual Download Page 28

28/67 

4.4.

 

Movement with the Wheel Set 

 

 

 

CAUTION 

Unsafe transport  

Personnel injury or property damage may result. 

 

No persons or objects may be on the masonry working platform during transport! 

 

Transport may only be done when the masonry working platform is lowered and all railing 
elements are removed. 

 

Only use suitable lifting and securing materials. 

 

 

 

WARNING 

Danger of crushing by a masonry platform without an operator 

Personnel injury or property damage are the result. 

 

Moving the masonry platform on wheels over inclines or declines is prohibited! 

 

Masonry working platform may only be moved if there are no persons or objects on the masonry 
working platform! 

 

The wheels may only be used for short stretches and on level concrete surfaces. 

 

Sequence 

 

Install wheel set in the holding plate. Move the platform down until the lower frame lifts off. 

 

Two persons can move the masonry work platform. 

 

To secure it, lift the masonry work platform and put the frame at the bottom onto the floor. 

 

Summary of Contents for MAB 2001




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands