![background image](http://html1.mh-extra.com/html/linn/sizmik-10-25/sizmik-10-25_manual_1925626002.webp)
ii
UK USERS PLEASE READ THIS IMPORTANT SAFETY INFORMATION
Fuse replacement
This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug
contains a 5 Amp fuse. If the fuse has blown it can be replaced as follows:
a) Pull out the red fuse cover/carrier.
b) Remove and dispose of the blown fuse.
c) Fit a new 5 Amp BS1362 approved fuse into the carrier and push the carrier
back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the
plug. Contact your Linn retailer to obtain a replacement fuse cover.
Fuses are for fire protection and do not protect against electric shock.
Mains plug replacement
Should your mains plug need replacing and you are competent to do this
proceed as follows. If you are in doubt contact your Linn retailer or a competent
electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection points of
most quality plugs.
Attach the wires securely to their respective points. The Brown wire must go to
the Live pin, the Blue wire must go to the Neutral pin, and the Green/Yellow wire
must go to the Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding the
outer sheath of the cable firmly and that the wires are correctly connected.
WARNING
THIS APPLIANCE MUST BE EARTHED.
Replacing the fuse
Should the mains fuse blow replace it only with an equivalent part. The fuse
holder is located just below the mains inlet socket. To replace the fuse
disconnect the product from the mains supply. Using a flat blade screwdriver
remove and replace the fuse. If the fuse blows a second time there is a fault in
the product. Contact your local retailer.
Fuse ratings.
See specifications section.
Mains voltage operating range
.
See specifications section.
CE Declaration of Conformity
Linn Products Ltd declare that this product is in conformance with the Low
Voltage Directive 73/23/EEC and Electromagnetic Compatibility 89/336/EEC as
amended by 92/31/EEC and 93/68/EEC.
The conformity of the designated product with the provisions of Directive
number 73/23/EEC (LVD) is proved by full compliance with the following
standards:
Standard number
Date of issue
Test type
EN60065
1993
General requirements
Marking
Ionizing
Heating under normal conditions
Shock hazards under normal
operating instructions
Insulation requirements
Fault conditions
Mechanical strength
Parts connected to the mains supply
Components
Terminal devices
External flexible cords
Electrical connections and
mechanical fixings
The conformity of the designated product with the provisions of Directive
number 89/336/EEC (EMC) is proved by full compliance with the following
standards:
Standard number
Date of issue
Test type
EN55013
1994
Conducted emissions
EN55013
1994
Absorbed emissions
EN60555-2
1987
Harmonics
EN60555-3
1987
Voltage fluctuations
EN55020
1994
Immunity
FCC notice
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.