LinMot C1150-DS-XC-0S Installation Manual Download Page 22

Page: 22 / 29

Installation Guide C1100

Page 22 of 29

0185-1062-E_6V12_IG_Drives_C1100

NTI AG / LinMot

Ordering Information

Drive

Description

Art. No.

C1100-GP-XC-0S-000

General Purpose Drive

72VDC/25Apeak

0150-2380

C1150-EC-XC-0S-000

ETHERCAT Drive

72VDC/25Apeak

0150-2382

C1150-DS-XC-0S-000

ETHERCAT CiA402 Drive

72VDC/25Apeak

0150-2417

C1150-SE-XC-0S-000

ETHERCAT SoE Drive

72VDC/25Apeak

0150-2625

C1150-PN-XC-0S-000

PROFINET Drive

72VDC/25Apeak

0150-2384

C1100-GP-XC-1S-000

General Purpose Drive

72VDC/25Apeak/STO

0150-2381

C1150-EC-XC-1S-000

ETHERCAT Drive

72VDC/25Apeak/STO

0150-2383

C1150-DS-XC-1S-000

ETHERCAT CiA402 Drive

72VDC/25Apeak/STO

0150-2418

C1150-SE-XC-1S-000

ETHERCAT SoE Drive

72VDC/25Apeak/STO

0150-2626

C1150-PN-XC-1S-000

PROFINET Drive

72VDC/25Apeak/STO

0150-2385

Accessories

Description

Art. No.

DC01-C1X00-0S/X1/X4

Drive Connector Set for C1X00-0S

0150-3527

DC01-C1X00-1S/X1/X4/X33

Drive Connector Set for C1X00-1S

0150-3528

DC01-C1X00/X1

Drive Connector for PWR 72VDC Input

0150-3525

DC01-C1X00/X2

Drive Connector Motor Phases

0150-3526

DC01-Signal/X4

Drive Connector 24VDC & Logic

0150-3447

DC01-Safety/X33

Drive Connector Safety

0150-3451

Isolated USB-RS232 converter Isolated USB RS232 converter with config. cable

0150-2473

RS232 PC config. Cable 2.5m

For C1100/C1250/E1200/E1400/M8000

0150-2143

Isolated USB-serial converter

Isolated USB RS232/422/485 converter

0150-3120

AS01-X4-DIP-SW-000

6 pole DIP switch for C1100-EC, on X4

0150-2498

Compatible Power Supplies

Art. No.

S01-24/500

Power Supply 24V/500W, 1x120/230VAC

0150-2480

S01-48/300

Power Supply 48V/300W, 1x120/230VAC

0150-1941

S01-48/600

Power Supply 48V/600W, 1x120/230VAC

0150-1946

S01-72/500

Power Supply 72V/500W, 1x120/230VAC

0150-1874

S01-72/1000

Power Supply 72V/1000W, 3x340-550VAC

0150-1872

T01-72/420-Multi

T-Supply 72V/420VA, 3x230/400/480VAC

0150-1869

T01-72/900-Multi

T-Supply 900VA, 3x230/400/480 VAC

0150-1870

T01-72/1500-Multi

T-Supply 1500VA, 3x230/400/480 VAC

0150-1871

T01-72/420 -1ph

T-Supply 420VA, 1x208/220/230/240VAC

0150-1859

Bold items are strongly recommended accessories!

The connectors have to be ordered separately and are not included with the drive!

Use isolated USB RS232 converter for configuration!

Summary of Contents for C1150-DS-XC-0S






























Search results

Summary of Contents for C1150-DS-XC-0S

Reviews:

Related manuals for C1150-DS-XC-0S

Brands by name

Popular brands

LinMot C1150-DS-XC-0S, Installation Manual

Search results

Summary of Contents for C1150-DS-XC-0S

Reviews:

Related manuals for C1150-DS-XC-0S

Brands by name

Popular brands