manualshive.com logo in svg

Linksys SRW2016, User Manual

Share
Download
Linksys SRW2016 User Manual Download Page 104

94

Chapter 5: Using the Web-based Utility for Configuration
Spanning Tree Tab on SRW2048 Switches - MSTP Interface Settings

WebView Switches

Spanning Tree Tab on SRW2048 Switches - MSTP Interface Settings

The 

MSTP Interface Settings

 screen contains parameters assigning MSTP settings to specific interfaces. 

Instance ID

. Lists the MSTP instances configured on the device. Possible field range is 1-15.

Interface

. Assigns either ports or LAGs to the selected MSTP instance. 

MSTP

. Indicates that MSTP is enabled on this interface.

Port State

. Indicates whether the port is enabled or disabled in the specific instance.

Type

. Indicates whether MSTP treats the port as a point-to-point port, or a port connected to a hub, and whether 

the port is internal to the MST region or a boundary port. A Master port provides connectivity from a MSTP region 
to the outlying CIST root. A Boundary port attaches MST bridges to LAN in an outlying region. If the port is a 
boundary port, it also indicates whether the device on the other side of the link is working in RSTP or STP mode.

Role

. Indicates the port role assigned by the STP algorithm in order to provide to STP paths. The possible field 

values are: 

Root - Provides the lowest cost path to forward packets to root device. 

Designated - Indicates the port or LAG via which the designated device is attached to the LAN. 

Alternate - Provides an alternate path to the root device from the root interface. 

Backup - Provides a backup path to the designated port path toward the Spanning Tree leaves. Backup ports 
occur only when two ports are connected in a loop by a point-to-point link. Backup ports also occur when a 
LAN has two or more connections connected to a shared segment.

Disabled - Indicates the port is not participating in the Spanning Tree.

Mode

. Mode of Spanning Tree protocol.

Interface Priority (0-240,in steps of 16)

. Defines the interface priority for specified instance. The default value 

is 128.

Path Cost

. Indicates the port contribution to the Spanning Tree instance. The range should always be 1-

200,000,000.

Figure 5-91: Spanning Tree - MSTP Interface Settings

NOTE:

Rapid STP is available on the 

SRW2048 Switches ONLY.

Summary of Contents for SRW2016




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands