Lightware MX2-16x16-DH-8DPi-A-R, User Manual

Page: 27 / 138

4. Front Panel Control MX2-HDMI20 series – User's Manual 27
Applied firmware package: v1.7.0 | LDC software: v2.5.1b5
▪
Left part and Right part
: The device supports vertical splitting of an HDMI 2.0 4k@60Hz 4:4:4 input signal
to left and right halves allowing for the transmission of an 18Gbps HDMI2.0 signal over two HDMI1.4
compliant links. The two halves can then be recombined at the signal destination. To apply the feature
route the same input signal to 2 output ports. Set the conversion to
Left part
on one output port and
Right part
on the other output port. See the Typical Application section.
Signal Type
▪
Auto
: the outgoing signal format is set automatically according to the audio presence in the video
stream: if audio is present, the signal format is HDMI.
▪
HDMI
: the outgoing signal format is forced to be HDMI.
▪
DVI
: the outgoing signal format is forced to be DVI.
HDCP #hdcp
▪
Depends on input:
the encryption level is determined according
to the settings on the input port and the source content/
device. If the incoming signal is not encrypted, then the
outgoing signal will not be encrypted either.
▪
Max. possible:
the highest supported level of encryption
(between the matrix and the sink) is applied (up to HDCP v2.2).
See more information about HDCP in HDCP Management section.
Scrambling #scrambling
HDMI 2.0 standard introduced the
Scrambling
to the TMDS encoding which helps to decrease the energy
peaks and hence the Electro Magnetic Interference (EMI). To maintain backward compatibility, HDMI 2.0
only requires the use of scrambling with data rates of above 3.4 Gbps per lane. The feature can be set on the
output ports to
Auto
/
Forced On
/
Forced Off
.
INFO: The
Auto
setting (recommended) allows the pseudo-random conversion at frequencies above the
threshold.
Forced on
and
Forced off
settings override this operation.
TMDS Clock Rate
However, the clock rate can be set to
1/10
or
1/40
if necessary, using the
Auto
setting is recommended.
Analog Audio Submenu
DIFFERENCE: Analog Audio submenu appears when there is an
analog audio output beside the chosen video port.
-A
or
-Audio
suffix
in the model name refers to the analog audio feature (see the Model
Comparison table about the analog audio availability).
Information about the Analog and the Embedded Audio signal are
displayed in this submenu.
▪ Audio Present
and
Audio Type
(signal info),
▪ Audio Mode
:
Off / DP or HDMI Only / Analog Only / DP or HDMI and Analog
.
▪ Analog Mute
▪ Analog Volume
: adjustable from 0 (-96dB) to 100% (0dB),
▪ Analog Balance
: adjustable from -100% to + 100% (0 = center).
3.2.4. EDID Menu
Advanced EDID Management is available in the front panel LCD menu which allows to view an EDID, switch,
or save it to the User EDID memory. See more information about EDID technology in EDID Management . The
EDID memory structure of the device can be found in the Sources and Destinations section.
View Submenu #edid
Select the desired EDID memory block:
Factory EDIDs, Last Attached
EDIDs, User EDIDs,
or
Emulated EDIDs
. Select the
Name
item and press
the knob. Use the jog dial to step between the EDIDs. The following
information can be checked:
▪
Preferred Resolution
▪
Monitor Name
▪
Audio Info
  
