•
P
ROGRAM
1
PUSH BUTTON
[1]
Pressing PROGRAM 1 will activate the first
preprogrammed sequence.
•
F
UNCTION PUSH BUTTONS
[2]
Selected functions may be activated by pressing
any of the four FUNCTION buttons. (See page 5)
•
P
ROGRAM
2
PUSH BUTTON
[3]
Pressing the PROGRAM 2 button activates the
second preprogrammed sequence.
•
C
URSOR CONTROL PUSH BUTTONS
[4]
The UP, DOWN, LEFT, RIGHT and ENTER buttons
may be used to select programming functions.
3
Installation and
Operation
1. The Time Clock mounts in the 4-gang rough-in box supplied to you with this information.
2. Connect the Time Clock according to the wiring diagram on page 4. Be sure all terminals are tightened and
that no bare copper is exposed. For BRTLCK see separate page (P/N 85-1055).
3. After all units have been installed and the system has been fully programmed and tested, carefully place all
wires into the rough-in box and screw the Time Clock in place using the four mounting screws provided.
4. Snap on the faceplate.
Susp.
Ignr.
PROGRAM 1
PROGRAM 2
Hol.
Disp.
1
2
3
4
Controls
Installation Procedure
WARNING
To avoid fire, damage to the controls, shock
or serious injury turn off power at fuses or
circuit breakers and test the circuits to make
sure that power is off before wiring. Use only
recommended wire. It is recommended that
qualified electrician perform this installation.
C
OMPLI
/B
RILLIANCE
II T
IME
C
LOCK
2
Description
Features
Specification
The CL-TCCO and BRTLCK are programmable Time Clocks that automate scene changes for up to 26 Compli
dimming systems or up to 26 rooms with the Brilliance II whole house system.
The Lightolier
®
Controls Time Clock is a solid-state device to be used in conjunction with the Compli/MultiSet/
MultiSet Pro dimming systems and Brilliance II whole house system in order to activate scene changes at the various
Compli/MultiSet/MultiSet Pro/Brilliance II systems.
The Time Clock mounts in a four-gang rough-in box (supplied) and wires to:
MultiSet/MultiSet Pro
Single line voltage
Brilliance II
CAT 5 (2-twisted pair)
Compli
Belden #8777
The Time Clock has the following basic features and capabilities:
•
Accepts up to 512 different commands
•
Performs two independent program sequences
•
Each room/scene change can occur on any or all days of the week
•
One-minute resolution between commands
•
Programmable password prevents tampering by unauthorized users
•
Commands can be programmed in two ways:
• Astronomically (hours:minutes before/after sunrise/sunset)
• By the time of day (hours:minutes, AM/PM)
•
To facilitate viewing, the display illuminates during programming. However, if a button is not pressed for 60
seconds, the display automatically reverts back to its standard appearance.
•
During power failure, programmed commands will remain in memory for approximately 10 years without
the need for battery back-up. Time will continue to increment for 24 hours.
Button labels
1.
The buttons on the Time Clock are labeled at the factory. These
labels can be changed easily to customize your system.
2.
Insert a small screwdriver into the indentation on the outside of a
button and carefully pry off the transparent plastic key cover.
CAUTION: Pry from the outside edge, as shown. Do not attempt to
insert screwdriver between the key covers.
3.
A label sheet has been provided to you. Remove the factory label
and insert a selected label into the plastic key cover.
4.
Snap the cover back over the button housing by pressing firmly on
the plastic key cover.
5.
Repeat steps 1-4 for all of the buttons you wish to label.
Susp.
Ignr.
PROGRAM 1
