background image

 

 

  

 

 

3 June 2022 

 

    

       Page | 3

 

Safety and Compliance 

 

SAVE THESE SAFETY INSTRUCTIONS 
This manual contains important instructions that must be followed during installation of a breezEV Charging Station. 
 

WARNINGS 

This manual contains important instructions for breezEV EVC-L2 series that shall be followed during installation, operation, and maintenance of the unit. 

1.

 

Read all the instructions before using this product. 

2.

 

This device should be supervised when used around children. 

3.

 

Do not put fingers into the electric vehicle connector. 

4.

 

Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation, or any other signs of damage. 

5.

 

Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage. 

6.

 

To reduce the risk of fire, connect only to a circuit provided branch circuit over-current protection in accordance with the CSA C22.1–15 Canadian 

Electrical Code, Part 1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70 National Electrical Code (USA). 

7.

 

To avoid a risk of fire or electric shock, do not use this device with an extension cord. 

8.

 

THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE, PART I, RULE 4-012, IS TO BE DETERMINED BY THE LOCAL 

INSPECTION AUTHORITY HAVING JURISDICTION. 

9.

 

Risk of electric shock. Do not remove cover or attempt to open the enclosure. No user serviceable parts inside. Refer servicing to qualified service 

personnel. 

 

AVERTISSEMENT – Ce manuel contient des instructions importantes pour les modèles: série EVC-L2 qui doit être suivie pendant l'installation, le fonctionnement 

et la maintenance de l'unité. 

1.

 

Lisez toutes les instructions avant d'utiliser ce produit. 

2.

 

Cet appareil doit être surveillé lorsqu'il est utilisé à proximité d'enfants. 

3.

 

Ne pas mettre les doigts dans le connecteur du véhicule électrique. 

4.

 

N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché, a une isolation cassée, ou tout autre signe de dommage. 

5.

 

N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré, ouvert ou montre toute autre indication de dommage. 

6.

 

Pour réduire les risques d'incendie, ne connecter qu'à un circuit protection contre les surintensités des circuits de derivation conformément à la norme 

canadienne CSA C22.1-15 Code électrique, partie 1 (Canada) ou NOM-001-SEDE Installations électriques (service public) (Mexique) ou ANSI / NFPA 

70 National Electrical Code (États-Unis). 

 

FCC Compliance Statement 

This device complies with part 15 of the FCC Rules. 

 

Operation is subject to the following two conditions: 

1.

 

This device may not cause harmful interference,  

2.

 

This device must accept any interference received, including interference that may cause undesired operation.  

 

Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the 

equipment. 

 

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment 

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference 

to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to 

correct the interference at his own expense. 

WIFI module: FCC ID:2AC7Z-ESPWROOM32D 

LTE module: FCC ID: XMR202008EC25AFXD 

 

To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during 

device operation. To ensure compliance, operations at closer than this distance is not recommended. 

 

DESIGN STANDARDS FOLLOWED

 

The following UL testing & certification protocols have been followed: 

UL 2594: Electric Vehicle Supply Equipment 
UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General Requirements 
UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: Requirements for Protection Devices for Use in Charging Systems 
UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles 
UL 62: Flexible Cords and Cables 
UL 991: Tests for Safety-Related Controls Employing Solid-State Devices 
UL 1998: Software in Programmable Components 
NFPA 70 Article 625: National Electrical Code, Electric Vehicle Charging System 
UL 840 (Clearance and Creepage)

 

 

WARRANTY STATEMENTS 

Please see breezEV Standard Limited Warranty & Ultimate-Guard Program Details, both located on our website.

 

 

 

Summary of Contents for breezEV EVC-L2-D Series































Reviews: