background image

13

  

(13)

inDOMO HP

 - Platform lift

FINAL TESTS

IM.TEC.028.EN_rev.10.2

   -  November 2015

All rights reserved

COPY FOR THE SUPPLIER

Final commissioning confirmation for lift N° ____________________________________________

The tests have been carried out with positive results  

 

SI

  

NO

in case of positive results, the lift can be considered compliant with the Italian law D.Lgs. 27.01.2010, 

n° 17.

Special notes :  ___________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

__________________________________________________________________

Date _______________  

Installer’s / verifier’s signature: ____________________________

The installer certifies to have carried out the installation  properly, because all the tests have given 

positive results. 

The manufacturer will compile the related EC declaration of conformity, and the installer will be able 

to apply the EC mark in the car.

The lift can be put into operation after the fulfilment of the requirements as per par. 5 of the 

President’s  Decree  n.  214  (Amendments  to  the  art.  12  of  the  President’s  Decree  n.  162  dated 

30.04.1999), dated 05.10.2010.

Summary of Contents for InDomo HP














Reviews: