background image

 10 

5”

+

+

+

+

+

+

+

+

+

+

+

+

.............................................................................      

6    OPTIONS MENU 

6.1  OPTIONS 1

LED ON

OPTIONS  1

Press the             button in order to enter insde the OPTIONS MENU 1  , press in sequence the        

buttonto advance in the selection , the blinking led will indicate the poeistion , with the      button it will be 

activated Red fixed Led , with the        button it is deactivated.    

No active function.     

Condominium: Command Step Open only.     

Mode: OPEN-STOP-CLOSE-STOP.     

Electric lock activation.      

The imput CLOSE becomes PHOTO1.      

The activation of PHOTO anticipates the closure.      

6.2  OPTIONS 2  

LED ON

OPTIONS 2

Press the             button for 5” in order to enter the OPTION MENU 2 , press in sequence the             button 

to advance in the selection the led blinking shows the position and with the      button it is activated , fixed 

red Led, with the         button it deactivates .    

Faster slowing-down speed.     

The exit Relè 12-13 becomes a COURTESY LIGHT     

Delay of safety interventions during movement.    

Funcioning with PRESENT MAN.      

.............................................................................      

Wait for 20” or press the           again to exit programming mode. 

+

No active function.     

Wait for 20” or press the           again to exit programming mode. 

+

button to enter the OPTION MENU 1. then press it again in sequence to scroll through the available

options. The flashing LEDS indicate the position and the corresponding option. By pressing the function is activated 

(red led on), by pressing button – the function is deactivated

s

Condo options: step command only opening

Change operating mode: OPEN-STOPCLOSE-STOP

The CLOSE input becomes PHOTO1.

Activating PHOTO anticipates closure.

then press it again in sequence to scroll

through the available options. The flashing LEDS indicate the position and the corresponding option. By pressing 

the function is activated (red led on), by pressing button – the function is deactivated

s

Increase the speed during slowdown

The output Relay 12 - 13 becomes COURTESY LIGHT.

Safety intervention delay during movement.

Operation in MAN'S SWITCH

OPEN-STOP-CLOSE-STOP

Summary of Contents for CT2 24 UNI DL













Reviews: