manualshive.com logo in svg

LiCONiC StoreX Series, Operating Manual

Share
Download
LiCONiC StoreX Series Operating Manual Download Page 20

 

StoreX

 

Series

  

 STX_V078.doc 

19

 CMa, 

23.11.2009 

Response Time 

~30  s 

Warm-Up Time 

5  min. operation 

MTBF 30’000 

hrs 

 

3.5.4 

O2 Oxygen Option 

The sensors for oxygen measurement are based on the same principles as 
described above. The main difference is the measurement range of the sensor 
used in the O2 option. 

Specifications 

Measuring Range 

0.1..95  % Vol. 

Input Pressure 

2 
8 

bar typ. 
bar max. 

Gas Flow 

~10  l/min max. 

Gas Consumption @ 25% O2, 20°C 

<__ 
~__ 
~__ 

l/h standby 
l/h 2-min.-access cycles 
l/h 30sec.-access cycles 

Accuracy ±0.5 

% 

FS 

Stability 

±0.5  % FS over 12 month 

Repeatability 

±1  % at full scale 

Response Time 

~30  s 

Warm-Up Time 

5  min. operation 

MTBF 30’000 

hrs 

 

 

WARNING ! 
 
O2-Option leads to increased explosion risk 

 

The maximum concentration of oxygen allowed with this option is limited to 25% 
O2 vol. for safety reasons. 

3.5.5 

Other Gassing Options 

There are other gassing options available. Please contact Liconic applications for 
further information.  

3.6 

UHS (Ultra High Speed) Option 

Applications with very short access times. The access speed of the UHS handler 
is almost double compared to standard High Speed handlers. Access time for 
UHS STX40 units is maximum ~12 seconds and for larger units access time is 
maximum ~20 seconds. Please ask for the latest specifications for your model. 

3.7 Customized 

Color 

Standard coating of the StoreX is RAL 9016. Other customized coating is 
possible. Please specify RAL code and/or send sample. Note that this option will  
increase delivery time. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for StoreX Series


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands