LG UM36FH Instruction Manual Download Page 39

Page: 39 / 71

THE INDOOR UNIT INSTALLATION

ENGLISH

Mounting the anchor nut and
bolt

- Prepare 4 suspension bolts. (Each bolts

length should be same.)

- Measure and mark the position for the

Suspension bolts and the piping hole.

- Drill the hole for anchor nut on the ceiling.

- Insert the nuts and washer onto the

suspension bolts for locking the suspension
bolts on the ceiling.

- Mount the suspension bolts to the

anchornuts firmly.

- Secure the hangers onto the Suspension

bolts (adjust level roughly.) using nuts,
washers and spring washers.

- Adjust a level with a level gauge on the

direction of left-right, back-forth by adjusting
suspension bolts.

- Adjust a level on the direction of top-bottom

by adjusting suspension bolts. Then the unit
will be declined to the bottomside so as to
drain well.

(Unit : mm)

Nut

Ceiling

Anchor nut

Washer

Suspension

bolts

Suspension

bolts

Spring

washer

Max.

12 mm

Nut

Suspension

bolts

Hangen

Washer

Suspension bol

Model (kBtu/h)

18 k/24 k

1 018

355

36 k/42 k/48 k/60 k

1 418

Installation information for declination

- Install declination of the indoor unit is

very important for the drain of the
convertible type air conditioner.

- Minimum thickness of the insulation

for the connecting pipe shall be 10
mm.

- If the Installation Plates are fixed to

horizontal line, the indoor unit after
installing will be declined to the
bottomside.

CAUTION

Summary of Contents for UM36FH








































































Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands

LG UM36FH, Instruction Manual

Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands