LG UM36FH Instruction Manual Download Page 6

Page: 6 / 71

SAFETY INSTRUCTIONS

ENGLISH

• Compliance with national gas regulations shall be observed.
• Ducts connected to an appliance shall not contain an ignition

source. (for R32)

Installation

• Always perform grounding.

- Otherwise, it may cause electrical shock.

• Don’t use a power cord, a plug or a loose socket which is

damaged.
- Otherwise, it may cause a fire or electrical shock.

• For installation of the product, always contact the service center or

a professional installation agency.
- Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the

service panel to the outdoor unit.
- If the electrical part cover of the indoor unit and the service panel

of the outdoor unit are not attached securely, it could result in a
fire or electric shock due to dust, water, etc.

• Always install an air leakage breaker and a dedicated switching board.

- No installation may cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air

conditioner.
- Otherwise, it may cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not

damaged due to use for a long time.
- It may cause injury or an accident.

• Do not disassemble or repair the product randomly.

- It will cause a fire or electrical shock.

• Do not install the product at a place that there is concern of falling

down.
- Otherwise, it may result in personal injury.

• Use caution when unpacking and installing.

- Sharp edges may cause injury.

• The appliance shall be stored in a room without continuously

operating open flames (for example an operating gas appliance)
and ignition sources (for example an operating electric heater).

Summary of Contents for UM36FH








































































Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands

LG UM36FH, Instruction Manual

Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands