LG UM36FH Instruction Manual Download Page 33

Page: 33 / 71

THE INDOOR UNIT INSTALLATION

ENGLISH

Remove

For Concealed Installation

Remove the 6 screws.

Remove the Upper Deco cover.

Remove the Side Deco covers.

For Side Piping

Remove the Deco Covers.

Remove the slit portions

Assemble the Deco Covers.

Preparation / For Moldings , Side
Piping, and Concealed Installation

For Moldings

Remove the slit portions on the Rear
Panel.

Upper
Deco cover

Side

Deco cover

Left bottom
piping

Right bottom
piping

Left/right piping

Right back piping

Wall

Left back
piping

Right back
piping

Refrigerant Piping

The location of hole is different depending
on which side of the pipe is taken out.

Drill a hole (Ø 70 mm)in the point indicated
by

symbol in the illustration as below

NOTE

The suggested shortest pipe length is
5 m, in order to avoid noise from the
outdoor unit and vibration.

(Unit: mm)

Summary of Contents for UM36FH








































































Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands

LG UM36FH, Instruction Manual

Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands