LG UM36FH Instruction Manual Download Page 23

Page: 23 / 71

THE INDOOR UNIT INSTALLATION

ENGLISH

THE INDOOR UNIT INSTALLATION

Use the ventilation fan
for smoke-collecting
hood with sufficient
capacity.

Cooking table

Air conditioner

Take enough
distance

Install the unit leaning to a drainage hole side
as a figure for easy water drainage.

NOTE

• Avoid the following installation location.
1. Such places as restaurants and kitchen

where considerable amount of oil
steam and flour is generated.
These may cause heat exchange
efficiency reduction, or water drops,
drain pump mal-function.
In these cases, take the following
actions;

• Make sure that ventilation fan is enough

to cover all noxious gases from this
place.

• Ensure enough distance from the

cooking room to install the air
conditioner in such a place where it may
not suck oily steam.

2. Avoid installing air conditioner in such

places where cooking oil or iron
powder is generated.

3. Avoid places where inflammable gas is

generated.

4. Avoid place where noxious gas is

generated.

5. Avoid places near high frequency

generators.

CAUTION

• This air-conditioner uses a drain pump.

• Install the unit horizontally using a level

gauge.

• During the installation, care should be

taken not to damage electric wires.

• Select and mark the position for fixing

bolts and piping hole.

• Decide the position for fixing bolts

slightly tilted to the drain direction after
considering the direction of drain hose.

• Drill the hole for anchor bolt on the

ceiling or wall.

Summary of Contents for UM36FH








































































Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands

LG UM36FH, Instruction Manual

Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands