LG UM36FH Instruction Manual Download Page 48

Page: 48 / 71

THE INDOOR UNIT INSTALLATION

ENGLISH

Precautions when laying power
wiring

Use round pressure terminals for connections
to the power terminal block.

When none are available, follow the
instructions below.

- Do not connect wiring of different

thicknesses to the power terminal block.
(Slack in the power wiring may cause
abnormal heat.)

- When connecting wiring which is the same

thickness, do as shown in the figure below.

Power wire

Round pressure terminal

Connect same thickness

wiring to both sides.

It is forbidden to

connect two to one

side.

It is forbidden to

connect wiring of

different thicknesses.

- For wiring, use the designated power wire

and connect firmly, then secure to prevent
outside pressure being exerted on the
terminal block.

- Use an appropriate screwdriver for tightening

the terminal screws. A screwdriver with a
small head will strip the head and make
proper tightening impossible.

- Over-tightening the terminal screws may

break them.

Summary of Contents for UM36FH








































































Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands

LG UM36FH, Instruction Manual

Search results

Summary of Contents for UM36FH

Reviews:

Related manuals for UM36FH

Brands by name

Popular brands