LG niagara4 MultiSITE Edge 10 User Manual Download

Page: 21 / 73

MS- E10 User Guide

Due to our policy of continuous product innovation, some specifications may change without notification.

CHAPTER 3: RUN THE

COMMISSIONING WIZARD

Topics covered in this chapter

•

Starting the Commissioning Wizard

•

Installing or updating licenses

•

Installing or updating licenses from files

•

Setting the enabled runtime profiles

•

Specifying a station database to install

•

Selecting modules to install or upgrade

•

Install/upgrade core software

•

TCP/IP configuration

•

Configuring system passphrase

•

Remove default platform user account

•

Configuring additional platform daemon users

•

Reviewing and finishing the Commissioning Wizard

As shown below, the Commissioning Wizard is a right-click option on any connected MS-E10 platform in the Nav tree. You can

also launch the wizard from the Platform Administration view.

Figure 8: Commissioning Wizard as right-click platform option

Use this wizard when installing a new MS-E10 device, as it provides a “checklist” method to perform essential (and often “one

time”) platform tasks. Also use this wizard whenever you upgrade the core Niagara 4 software in the MS-E10 device, at some

future time. See the Niagara Platform Guide for more details.

Summary of Contents for niagara4 MultiSITE Edge 10










































































Search results

Summary of Contents for niagara4 MultiSITE Edge 10

Reviews:

Related manuals for niagara4 MultiSITE Edge 10

Brands by name

Popular brands

LG niagara4 MultiSITE Edge 10, User Manual

Search results

Summary of Contents for niagara4 MultiSITE Edge 10

Reviews:

Related manuals for niagara4 MultiSITE Edge 10

Brands by name

Popular brands