LG niagara4 MultiSITE Edge 10 User Manual Download Page 32 | Manualshive

Page: 32 / 73

background image

MS- E10 User Guide

Due to our policy of continuous product innovation, some specifications may change without notification.

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp. 32

Note:

IPv6 support is available; however this document focuses on IPv4 configuration. For details on IPv6, refer to the Niagara

Platform Guide section on TCP/IP Configuration.

Daisy chain mode

By default the MS-E10 device is factory shipped in the daisy chain link mode. The Daisy Chain/STP settings are configured

during the TCP/IP step of the Commissioning Wizard and during distribution file install procedure.

Note:

The STP settings are available only when Link Mode is configured for Daisy Chain.

Figure 19: Link Settings in TCP/IP Configuration

Configuring TCP/IP settings

Perform the following steps to configure the device’s TCP/IP settings.
Step 1: Review the Interface 1 settings on the IPv4 Settings tab, which include the temporary factory- shipped IP address.
Step 2: Assign the MS-E10 device a unique IPv4 address for the network you are installing it on. No other device on this network

should use this same IP address. Include the appropriate subnet mask used by the network.

«
...
30
31
32
33
34
...
»

Summary of Contents for niagara4 MultiSITE Edge 10










































































Reviews:

No comments

Related manuals for niagara4 MultiSITE Edge 10

Brand: Valve Concepts Pages: 15

Brand: Febco Pages: 4

Brand: Cisco Pages: 48

Brand: TCS Basys Controls Pages: 2

Brand: C3 Custom Coolers Pages: 16

Brand: Jands Pages: 7

coviva Smartbox TKP100A

Brand: hager Pages: 34

Brand: ICP DAS USA Pages: 166

Brand: ICP DAS USA Pages: 5

Brand: ICP DAS USA Pages: 64

Brand: ICP DAS USA Pages: 7

Tunnel Master Jr

Brand: ICS Pages: 83

PROFIBUS PROFI-2510

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 40

Brand: Magellan Pages: 2

Brand: National Instruments Pages: 8

Brand: Unitech Pages: 55

Brand: S&C Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands