background image

LIP-6812 & LIP-6830 

 

Installer Guide 

19 June, 

‘07

 

3)  Press        button, or move cursor to 

8.VLAN Settings 

using the 

[Next]/[Prev]

 Softkeys, and 

press the 

[ OK ]

 Softkey. 

4)  Press      button, or move cursor to 

1.VLAN Priority (LAN) 

using the 

[Next]/[Prev]

 Softkeys, 

and press the 

[ OK ]

 Softkey. 

5)  Input the VLAN Priority for the LAN port using the dial pad. 

 
6) Press 

the 

[ OK ]

 Softkey to save your Configuration. 

7)  Press the                 button to exit from the menu. 

 

 

Changing the VLAN Priority for the LAN port requires a reboot of the LIP-6812/LIP-
6830; when you leave the menu, you will receive a Reboot notice. 

 

A VLAN priority of 5 for the LAN port is recommended. 

 

To disable VLANs, assign the VLAN ID as ‘0’. 

 

3.4.8.2  VLAN ID (LAN) 

The VLAN ID (LAN) assigns the identification for Ethernet frames for the LIP-6812/LIP-6830 
voice port including signaling and voice payloads.  Setting VLAN ID to 0 disables the VLAN 
framing and only standard Ethernet frames are sent. 
 
To assign VLAN ID for the LAN (voice) port: 
1)  Press the            button. If the LCD Menu is locked, use the unlock procedure (refer to 

Section 

 3.3

 Lock/Unlock Configuration). 

2)  Press     button, or move cursor to 

1.Network Configuration

 using the 

[Next]/[Prev]

 

Softkeys, and press the 

[ OK ]

 Softkey.  

3)  Press       button, or move cursor to 

8.VLAN Settings 

using the 

[Next]/[Prev]

 Softkeys, and 

press the 

[ OK ]

 Softkey. 

4)  Press       button, or move cursor to 

2.VLAN ID (LAN) 

using the 

[Next]/[Prev]

 Softkeys, and 

press the 

[ OK ]

 Softkey. 

5)  Input the VLAN ID for the LAN port using the dial pad. 

 
6) Press 

the 

[ OK ]

 Softkey to save your Configuration. 

7)  Press the                 button to exit from the menu. 

VLAN Priority (LAN)[0~7]

 [ 

»

 ] [CLR ] [ OK ]  

VLAN ID (LAN)[0-4094] 

 [ 

»

 ] [CLR ] [ OK ] 

 

Summary of Contents for LIP-6812









































































































































Reviews: