manualshive.com logo in svg

Lexmark OptraImage 443, Service Manual

Share
Download
Lexmark OptraImage 443 Service Manual Download Page 25

2-5

2.4.2

2.4.2

2.4.2

2.4.2

 

SCSI Signal  Connection

SCSI Signal  Connection

SCSI Signal  Connection

SCSI Signal  Connection

The devices linked to the SCSI interface are daisy-chained with each other. A terminator is
attached to both ends of the SCSI daisy-chained cable. User can buy the SCSI cable at electronic or
computer stores. The specifications of the SCSI cable is as below:

Name:

SCSI Cable

Cable Specification:

50 pins or 25 pins to 50 pins, shielded Amphenol

Cable Length:

less than or equal to 6 meters

2.4.2.1

2.4.2.1

2.4.2.1

2.4.2.1

 

SCSI Cable Connection

SCSI Cable Connection

SCSI Cable Connection

SCSI Cable Connection

The scanner is shipped with the SCSI cable.  The SCSI cable is used to connect your scanner and printer.
Connect the SCSI cable in this step, but do not turn the power on yet.

There are two configurations for the connection.

Configuration I: The number of devices attached to the SCSI bus (including the host PC) is three.  The

Configuration I: The number of devices attached to the SCSI bus (including the host PC) is three.  The

Configuration I: The number of devices attached to the SCSI bus (including the host PC) is three.  The

Configuration I: The number of devices attached to the SCSI bus (including the host PC) is three.  The
scanner is located in the middle of the connection, as shown below.

scanner is located in the middle of the connection, as shown below.

scanner is located in the middle of the connection, as shown below.

scanner is located in the middle of the connection, as shown below.

1. Set scanner’s SCSI terminator switch off.

2. Plug one end of the SCSI cable into the SCSI connector of the host PC, and the other end of
    the cable to the scanner.

3. Plug one end of the SCSI cable into the SCSI connector of the third device, and the other end of the

cable to the other scanner.

Terminator

Set terminator

switch at “off”

position

Terminator

Scanner

SCSI device

Host PC

Summary of Contents for OptraImage 443

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands