Leuze electronic BPS 301i Original Operating Instructions Download

Page: 68 / 93

Diagnostics and troubleshooting

Leuze electronic

BPS 301i

Table 10.1:

PWR LED displays – causes and measures

10.3 Error messages on the display

Via the optional display of the BPS, the device outputs the following possible error status information while

it has the

BPS Info

device status:

•

System OK

BPS operating error-free.

•

Warning

•

Error

Device function is not ensured.

Figure 10.2: Example: Device status/error status information on the display

10.4 Checklist for causes of errors

Table 10.2:

Service interface errors – causes and measures

Error

Possible cause

Measures

Off

• No supply voltage connected

to the device

• Hardware error

• Check supply voltage

• Contact Leuze electronic customer

service (see chapter 12 "Service and sup

port")

Red, flashing

• No bar code in the scanning

beam

• No valid measurement value

• Query BCB diagnostic data and carry out

the resulting measures (see table 10.5)

Orange, continuous

light

• Device in

Service

mode

• Reset the device to

Process

mode using

the webConfig tool

BPS Info

System OK

Error

Possible cause

Measures

webConfig does not

start

• Incorrectly connected intercon

nection cable

• Connected BPS is not recog

nized

• No communication via USB

service interface

• Old webConfig configuration in

the browser cache

• Check interconnection cable

• Install USB driver

• Clear browser history

Summary of Contents for BPS 301i






























































































Search results

Summary of Contents for BPS 301i

Reviews:

Related manuals for BPS 301i

Brands by name

Popular brands

Leuze electronic BPS 301i, Original Operating Instructions

Search results

Summary of Contents for BPS 301i

Reviews:

Related manuals for BPS 301i

Brands by name

Popular brands