background image

Safety

Leuze electronic

BPS 301i

10

1

Laser aperture

2

Laser warning sign

3

Laser information sign with laser parameters

Figure 2.1: Laser aperture, laser warning and information signs

NOTICE
Affix laser information and warning signs!
Laser information and warning signs attached to the device(see figure 2.1). Also included with the device 

are self-adhesive laser warning and laser information signs (stick-on labels) in multiple languages (see 

figure 2.2).

Affix the laser information sheet to the device in the language appropriate for the place of use.
When using the device in the U.S.A., use the stick-on label with the “Complies with 21 CFR 1040.10” 

notice.

Affix the laser information and warning signs near the device if no signs are attached to the device (e.g. 

because the device is too small) or if the attached laser information and warning signs are concealed 

due to the installation position.
Affix the laser information and warning signs so that they are legible without exposing the reader to the 

laser radiation of the device or other optical radiation.

2

1

3

Summary of Contents for BPS 301i






























































































Reviews: