background image

2

1

When installing this product, be sure to follow the instructions given in the manual!

● When performing maintenance operations (for example parts replacement), be sure to wear 
goggles or eye protection.
● Please contact us for information on the product not covered by this manual.
● The motor is amoving parts could cause injury, so please kindly take care.
● Giving too much of your attention to the display while riding can lead to an accident.
● It is important to check that the wheels are properly attend to the bicycle before commencing 
riding. If the wheels are not securely attached fixed serious injury may result.
● When riding a pedal-assisted electric bicycle, you should be fully familiar with the starting-off 
characteristics of the e-bike before riding it. If the e-bike starts off suddenly, accidents may result.
● It is important to turn on the lights when riding in the evening and at the place in low light 
situation.
● When cabling the product or installing the parts onto the e-bike, be sure to disconnect the 
battery. Not doing so may result in electric shock.
● When installing this product, be sure to follow the instructions given in the manual. If bolts and 
nuts are not tightened correctly or if the product is damaged, the e-bike may suddenly fall over 
and serious injury may result.
● The frequency of maintenance will vary depending on the usage of the e-bike. The chain should 
be cleaned periodically using an appropriate chain cleaner. Do not use alkaline or acidic cleaning 
agents to remove rust under any circumstances. If such cleaning agents are used, they may 
damage the chain and serious injury may result.

● Keep the motor and display away from water and heat sources.
● Do not connect positive and negative terminals.
● Keep the kit away from children and pets.
● Do not disassemble any part of the kit.
● Do not subject the kit to shocks (e.g. by dropping).
● In the unlikely event of the kit catching fire, DO NOT attempt to put it out with water. Use sand 
or another fire retardant instead and call emergency services immediately.
● This product is not intended for use by persons (including children) with reduced physical, 
sensory or mental capabilities or persons lacking experience and knowledge in using the product.
● Do not modify the system. Doing so may lead to malfunction of the system.
● Please consult the nearest dealer for any errors or problems.
● The product should be avoid wading, flooding when using.
● The vehicle should be parked in the ventilated dry warehouse, should not park in the wet, acid 
and alkali, also should not coexist with magnetic items.
● When transporting the product on a car in wet weather, put it in a safe place to stop it from 
getting wet due to the rain. what's more, please add some protector against rain.
● Do not clean the bicycle with a high-pressure water spray. If water gets into any of the compo-
nents, operation problems or rusting may result.
● The product should not be used for a long time overload, overload.
● Some important information given in this manual may also be found on the product labels.

Das-kit reserves the right to modify the technical data without prior notice.
The picture is for reference only, please be subject to the actual products.

- It is recommended that you use only genuine parts of the kit at all times. Serious injury 

  may result if loosen or faulty bolts and nuts.

- If the product is improperly adjusted, accidents and serious injury will be occurred.

- Keep this manual in a safe place for later reference.

For Your Safety

Notes

Summary of Contents for MKL6BTFM Series









Reviews: