Lenovo ThinkPad 390 Setup Manual Download Page 61

Page: 61 / 70

Models:

ThinkPad model 570

Issue:

After docking or undocking computer, the printer device connected to the
computer’s parallel port does not function.

Cause:

This problem is a known system BIOS issue.

Resolution:

IBM plans to eventually update the BIOS to address this issue.

2.7 After undocking the computer, the Fn function key and AC/DC power

generated events might not function properly

Models:

ThinkPad model 570

Issue:

After undocking the computer, the Fn function key and AC/DC power
generated events might not function properly.

Cause:

This problem is a known system BIOS issue.

Resolution:

If this should occur, place the system into Standby from the Start menu, then
wake–up the system to recover. IBM plans to eventually update the BIOS to
address this issue.

Summary of Contents for ThinkPad 390







































































Search results

Summary of Contents for ThinkPad 390

Reviews:

Related manuals for ThinkPad 390

Brands by name

Popular brands

Lenovo ThinkPad 390, Setup Manual

Search results

Summary of Contents for ThinkPad 390

Reviews:

Related manuals for ThinkPad 390

Brands by name

Popular brands