Lenovo ThinkPad 390 Setup Manual Download Page 43 | Manualshive

Page: 43 / 70

Lenovo ThinkPad 390 Setup Manual Download Page 43

Using docking station s or port replicators with APM-supported ThinkPad
models

On APM-supported ThinkPad models, Windows 2000 does not support dynamic docking or
undocking with docking stations or port replicators.  Most of the devices located in the
docking station or port replicator can only be configured when the computer is turned on or
restarted. PC Card, CardBus, and USB devices are exceptions to this restriction. Hot
insertion and removal of these devices in the docking station or port replicator are supported.

The following tables illustrate the type of docking  device support on Windows 2000
Professional for APM-supported  ThinkPad models:

ThinkPad 760Xx and 765D/L

ThinkPad 770

Hot

Dock

Warm

Dock

Cold

Dock

Hot

Dock

Warm

Dock

Cold

Dock

SelectaDock-II

IDE device

-

-

ü

-

-

ü

ISA card

(ISA Plug-and-Play, only
on startup or restart)

-

-

ü

-

-

ü

16-bit PC Card

-

-

ü

-

-

ü

CardBus PC Card

-

-

No support

-

-

No support

PCI card

-

-

ü

-

-

ü

GamePort

-

-

ü

-

-

ü

SCSI device

-

-

ü

-

-

ü

SelectaDock-III

IDE device

-

-

ü

-

-

ü

ISA

(ISA Plug-and-Play, only
on startup or restart)

-

-

ü

-

-

ü

16-bit PC Card

-

-

No support

-

-

ü

CardBus PC Card

-

-

ü

-

-

ü

PCI device

-

-

ü

-

-

ü

USB device

-

-

ü

-

-

ü

Game port

-

-

ü

-

-

ü

SCSI device

-

-

ü

-

-

ü

PC Card Enabler

16-bit PC Card

-

-

No support

-

-

ü

CardBus PC Card

-

-

ü

-

-

ü

PC Card Enabler with
Advanced EtherJet Port

16-bit PC Card

-

-

-

-

-

ü

CardBus PC Card

-

-

-

-

-

ü

Ethernet port

-

-

-

-

-

ü

ThinkPad 380E, 380 X, 560E,

and 560X

Hot

Dock

Warm

Dock

Cold

Dock

Enhanced Port Replicator

16-bit PC Card

-

-

ü

«
...
41
42
43
44
45
...
»

Summary of Contents for ThinkPad 390







































































Reviews:

No comments