manualshive.com logo in svg

Lenovo ThinkPad 390, Setup Manual, Page: 70 / 70

Share
Download
Lenovo ThinkPad 390 Setup Manual Download Page 70

 

10  Miscellaneous 

  

10.1   If moving the pointing device while changing the display mode (using the 

Notebook Manager), the pointer cursor becomes uncontrollable 

 

Models: 

ThinkPad i Series 2611 

Issue: 

When using the Notebook Manager to change the display mode 
(LCD/CRT/BOTH) on your computer and moving the mouse pointer at the 
same time, the pointer device will become uncontrollable. 

Cause: 

This is caused by a timing issue.  When VGA BIOS and the pointer device 
driver are simultaneously called, this will cause the pointer device to behave 
uncontrollably. 

Resolution: 

When changing the display mode using the Notebook Manager, do not move 
the pointer device. 

 
 

10.2   When transferring a file using the Infrared device at 4 Mbps from a computer 

running Windows 2000 to a computer running Windows 98, the file transfer 
fails 

 

Models: 

All ThinkPad models  

Issue: 

When transferring a file using the Infrared device at 4 Mbps from a computer 
running Windows 2000 to a computer running Windows 98, the file transfer 
fails. 

Cause: 

This is a Windows 98 problem. 

Resolution: 

If using the Infrared device to transfer files between computers running 
Windows 2000 and Windows 98, set the connection rate between the 
communicating computers to 115 kbps. 

 
 

10.3  The OS/2 Boot Manager does not work after restating Windows 2000 

and cannot start up the computer 

 

Models: 

ThinkPad all models 

Issue: 

The OS/2 boot manager does not work after restarting Windows 2000. 

Cause: 

Windows 2000 problem. 

Resolution: 

Do not use the OS/2 Boot Manager while running Windows 2000.  The OS/2 
Boot Manager is currently not supported under Windows 2000. 

 

Summary of Contents for ThinkPad 390







































































Reviews:

No comments