Lenovo ThinkCentre E73 Hardware Maintenance Manual Download Page 4

Page: 4 / 190

Locating connectors, controls, and indicators
on the front of your computer . . . . . . .

Locating connectors on the rear of your
computer . . . . . . . . . . . . . . .

Locating major FRUs and CRUs . . . . . .

Looking up FRU information . . . . . . .

Locating parts on the system board

. . . .

Locating internal drives . . . . . . . . .

Chapter 9. Replacing FRUs (machine
types: 10AS and 10AU) . . . . . . . .

Handling static-sensitive devices . . . . . . .

Installing or replacing hardware . . . . . . . .

Installing external options

. . . . . . . .

Removing the computer cover. . . . . . .

Removing and reinstalling the front bezel . .

Installing or replacing a PCI Express card . .

Installing or replacing a memory module . . .

Replacing the rear fan assembly . . . . . .

Replacing the battery . . . . . . . . . .

Replacing the primary hard disk drive . . . .

Installing the solid-state drive . . . . . . .

Replacing the optical drive . . . . . . . .

Replacing the slim card reader

. . . . . .

Replacing the power supply assembly

. . .

101

Replacing the heat sink and fan assembly . .

102

Replacing the thermal sensor . . . . . . .

104

Replacing the microprocessor . . . . . . .

106

Replacing the system board

. . . . . . .

109

Replacing the front audio and USB
assembly . . . . . . . . . . . . . . .

111

Replacing the Wi-Fi units . . . . . . . . .

112

Installing or removing the rear Wi-Fi
antenna

. . . . . . . . . . . . . . .

118

Installing or removing the front Wi-Fi
antenna

. . . . . . . . . . . . . . .

119

Replacing the keyboard or mouse . . . . .

121

Completing the parts replacement . . . . .

122

Chapter 10. Replacing FRUs
(machine types: 10AU, 10AW, 10BF,
and 10BG) . . . . . . . . . . . . . .

125

Handling static-sensitive devices . . . . . . .

125

Installing or replacing hardware . . . . . . . .

125

Installing external options

. . . . . . . .

125

Removing the computer cover. . . . . . .

126

Removing and reinstalling the front bezel . .

127

Accessing the system board components and
drives . . . . . . . . . . . . . . . .

128

Installing or replacing a PCI Express card . .

129

Installing or replacing a memory module . . .

131

Replacing the battery . . . . . . . . . .

133

Replacing the hard disk drive . . . . . . .

134

Replacing the optical drive . . . . . . . .

136

Replacing the slim card reader

. . . . . .

140

Replacing the solid-state drive

. . . . . .

143

Replacing the power supply assembly

. . .

147

Replacing the heat sink and fan assembly . .

151

Replacing the thermal sensor . . . . . . .

154

Replacing the microprocessor . . . . . . .

156

Replacing the system board

. . . . . . .

159

Replacing the system fan assembly

. . . .

161

Replacing the front audio and USB
assembly . . . . . . . . . . . . . . .

163

Replacing the Wi-Fi units . . . . . . . . .

165

Installing or removing the rear Wi-Fi
antenna

. . . . . . . . . . . . . . .

169

Installing or removing the front Wi-Fi
antenna

. . . . . . . . . . . . . . .

171

Replacing the keyboard or mouse . . . . .

173

Completing the parts replacement . . . . .

174

Chapter 11. Additional service
information . . . . . . . . . . . . .

177

Security features . . . . . . . . . . . . . .

177

Hardware-controlled passwords . . . . . .

177

Operating system password

. . . . . . .

177

Vital Product Data

. . . . . . . . . . .

177

BIOS levels . . . . . . . . . . . . . . . .

177

Flash update procedures

. . . . . . . . . .

177

Updating (flashing) the BIOS from a disc. . .

178

Updating (flashing) the BIOS from your
operating system . . . . . . . . . . . .

179

Recovering from a POST and BIOS update
failure . . . . . . . . . . . . . . . .

179

Power management

. . . . . . . . . . . .

180

Advanced configuration and power interface
(ACPI) BIOS . . . . . . . . . . . . . .

180

Automatic Power-on features . . . . . . .

180

Appendix A. Notices . . . . . . . . .

181

Television output notice . . . . . . . . . . .

182

European conformance CE mark . . . . . . .

182

Trademarks . . . . . . . . . . . . . . . .

182

Index. . . . . . . . . . . . . . . . .

183

ThinkCentre E73 Hardware Maintenance Manual

Summary of Contents for ThinkCentre E73































































































































































































Search results

Summary of Contents for ThinkCentre E73

Reviews:

Brands by name

Popular brands

Lenovo ThinkCentre E73, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkCentre E73

Reviews:

Brands by name

Popular brands