manualshive.com logo in svg

Lenovo ThinkCentre E73, Hardware Maintenance Manual

Share
Download
Lenovo ThinkCentre E73 Hardware Maintenance Manual Download Page 139

4. Note the location of the four screws

1

that secure the hard disk drive. Then, pivot the drive bay

assembly upward.

3

4

5

6

Figure 71. Pivoting the drive bay assembly

5. Hold the hard disk drive and remove the four screws that secure the hard disk drive. Then, remove

the hard disk drive from the drive bay assembly.

3

4

5

6

Figure 72. Removing the hard disk drive

6. Disconnect the signal cable and the power cable from the hard disk drive to completely remove the hard

disk drive from the chassis.

7. Connect one end of the signal cable to the rear of the new hard disk drive and the other end to an

available SATA connector on the system board. See “Locating parts on the system board” on page 79.
Then, locate an available five-wire power connector and connect it to the rear of the new hard disk drive.

Chapter 10

.

Replacing FRUs (machine types: 10AU, 10AW, 10BF, and 10BG)

135

Summary of Contents for ThinkCentre E73































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands