manualshive.com logo in svg

Lenovo ThinkCentre E73, Hardware Maintenance Manual

Share
Download
Lenovo ThinkCentre E73 Hardware Maintenance Manual Download Page 110

8. Insert the connector and cable of the new thermal sensor into the hole

1

in the chassis. Then align the

two tabs on the plastic holder holding the thermal sensor with the two holes

1

and

2

in the chassis,

and push the plastic holder until it snaps into position.

Figure 38. Installing the new thermal sensor

9. Reconnect the thermal sensor cable to the system board. See “Locating parts on the system board”

on page 72.

10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 83.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 122.

Replacing the microprocessor

Attention:

Do not open your computer or attempt any repair before reading and understanding “Important safety information”
on page 1.

This section provides instructions on how to replace the microprocessor.

CAUTION:

106

ThinkCentre E73 Hardware Maintenance Manual

Summary of Contents for ThinkCentre E73































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands