manualshive.com logo in svg

Lenovo ThinkCentre E73, Hardware Maintenance Manual

Share
Download
Lenovo ThinkCentre E73 Hardware Maintenance Manual Download Page 36

Table 2. Programs in Control Panel (continued)

Program

Control Panel section

Green text in Control Panel

Rescue and Recovery

System and Security

Lenovo - Enhanced Backup and
Restore

System Update

System and Security

Lenovo - Update and Drivers

View Management Utility

System and Security

Lenovo View Management Utility

Note:

Depending on your computer model, some of the programs might not be available.

Accessing Lenovo programs on the Windows 8 operating system

If your computer is preinstalled with the Windows 8 operating system, you can access Lenovo programs
by doing the following:

Press the Windows key to go to the Start screen. Click a Lenovo program to launch it. If you cannot find the
program you need, move the pointer to the bottom-right corner of the screen to display the charms. Then
click the

Search

charm to search for the desired program.

Your computer supports the following Lenovo programs:

• Fingerprint Software

• Lenovo Companion

• Lenovo Solution Center

• Lenovo Support

• Password Manager

• System Update

Lenovo Support Web site

Technical support information is available on the Lenovo Support Web site at:
http://www.lenovo.com/support

This Web site is updated with the latest support information such as the following:

• Drivers and software

• Diagnostic solutions

• Product and service warranty

• Product and parts details

• User guides and manuals

• Knowledge base and frequently asked questions

32

ThinkCentre E73 Hardware Maintenance Manual

Summary of Contents for ThinkCentre E73































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands