manualshive.com logo in svg

Lenovo ThinkCentre E73, Hardware Maintenance Manual

Share
Download
Lenovo ThinkCentre E73 Hardware Maintenance Manual Download Page 16

• A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aqui

pode resultar em exposição prejudicial à radiação.

PERIGO

Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da Classe 3B. Observe o seguinte:

Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou com instrumentos ópticos e
evite exposição direta ao feixe.

≥18 kg (37 lbs)

≥32 kg (70.5 lbs)

≥55 kg (121.2 lbs)

CUIDADO:

Utilize procedimentos de segurança para levantar equipamentos.

CUIDADO:

O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação
não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo
de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de
alimentação estejam desconectados da fonte de alimentação.

1

2

12

ThinkCentre E73 Hardware Maintenance Manual

Summary of Contents for ThinkCentre E73































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands