Lenovo RackSwitch G7028 Installation Manual Download Page 24

Page: 24 / 86

G7028 Installation Guide

SFP+ LEDs

Status LEDs for the SFP+ ports are described in the following table.

RJ-45 Ports

There are twenty-four 10/100/1000BASE-T Gigabit Ethernet (GbE) RJ-45 ports on

the front of the G7028.

To attach an RJ-45 connector to the switch, push the RJ-45 cable connector into the

port connector until it clicks into place.

Note:

Shielded twisted-pair cables are recommended for use with the RJ-45

management port.

RJ-45 LEDs

The RJ-45 port LEDs are oriented as shown

Figure 5

Figure 6. RJ-45 port status LEDs

Status LEDs for the RJ-45 ports are described in the following table.

Table 4. SFP+ port status LED behavior

LED

State

Functional Meaning

Link/Activity

Steady green

Link up

Off

No link

Flashing green

Activity

Table 5. RJ-45 port status LED behavior

LED

State

Functional Meaning

Link/Activity

Steady green

Link up

Off

No link

Flashing green

Activity

Speed

Steady green

100/1000 Mbps

Off

10 Mbps or no link

Link/Activity LED

Speed LED

Summary of Contents for RackSwitch G7028























































































Search results

Summary of Contents for RackSwitch G7028

Reviews:

Related manuals for RackSwitch G7028

Brands by name

Popular brands

Lenovo RackSwitch G7028, Installation Manual

Search results

Summary of Contents for RackSwitch G7028

Reviews:

Related manuals for RackSwitch G7028

Brands by name

Popular brands