Lenovo RackSwitch G7028 Installation Manual Download Page 17

Page: 17 / 86

Chapter 1: The RackSwitch G7028

Related Documentation

Additional or updated product documents may be available from the Lenovo

website. Such documents may cover features not described in the original

documentation that comes with the switch, or may include technical updates or

corrections.

You can obtain up-to-date information on the Lenovo support website:

http://support.lenovo.com/

Note:

Changes are made periodically to the Lenovo website. Procedures for

locating firmware and documentation might vary slightly from what is

described in this document.

For information about switch hardware and firmware features, specifications, and

standards, including their configuration, see the

Application Guide

for your specific

switch and its installed firmware.

For information about the switch information, statistics, and individual configuration

parameters, see the

Command Reference

guide for your specific switch and its

installed firmware.

For a list of compatible switch components and options (such as rack-mounting kits,

modules, cords, and cables), see the

Lenovo Networking Catalog

Summary of Contents for RackSwitch G7028























































































Search results

Summary of Contents for RackSwitch G7028

Reviews:

Related manuals for RackSwitch G7028

Brands by name

Popular brands

Lenovo RackSwitch G7028, Installation Manual

Search results

Summary of Contents for RackSwitch G7028

Reviews:

Related manuals for RackSwitch G7028

Brands by name

Popular brands