Lenovo RackSwitch G7028 Installation Manual Download Page 13

Page: 13 / 86

Safety Information

Statement 37

DANGER

Other Important Safety Notices

Important

This product is also designed for IT power distribution systems with phase-to-phase

voltage of 230V.

This product is not intended for use in the direct field of view at visual display

workplaces.

Important

Machinenlärminformations-Verordnung—3. GPSGV, der höchste Shalldruckpegel

beträgt 70 dB (A) oder weniger.

When you populate a rack cabinet, adhere to the following guidelines:

•

Always lower the leveling pads on the rack cabinet.

•

Always install the stabilizer brackets on the rack cabinet.

•

Always install the heaviest devices in the bottom of the rack cabinet.

•

Always install devices starting from the bottom of the rack cabinet.

•

Do not extend multiple devices from the rack cabinet simultaneously,
unless the rack-mounting instructions direction you to do so. Multiple
devices extended into the service position can cause your rack cabinet
to tip.

•

If you are not using the Lenovo 9308 rack cabinet, securely anchor the
rack cabinet to ensure its stability.

Summary of Contents for RackSwitch G7028























































































Search results

Summary of Contents for RackSwitch G7028

Reviews:

Related manuals for RackSwitch G7028

Brands by name

Popular brands

Lenovo RackSwitch G7028, Installation Manual

Search results

Summary of Contents for RackSwitch G7028

Reviews:

Related manuals for RackSwitch G7028

Brands by name

Popular brands