manualshive.com logo in svg

Lenovo 70AL, Maintenance Manual, Page: 43 / 190

Share
Download
Lenovo 70AL Maintenance Manual Download Page 43

ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter)

The following illustration shows the connectors on the ThinkServer RAID 700 Adapter.

Figure 17. ThinkServer RAID 700 Adapter

1

Ports 7-4

3

ThinkServer RAID 700 Battery connector

2

Ports 3-0

1

Ports 7-4

Used to connect a mini-SAS signal cable. See “Connecting the cables” on page 35.

2

Ports 3-0

Used to connect a mini-SAS signal cable. See “Connecting the cables” on page 35.

3

ThinkServer RAID 700 Battery connector

Used to connect a ThinkServer RAID 700 Battery. See “Installing or removing the ThinkServer RAID 700
Battery” on page 88.

Hot-swap hard disk drive backplane

Your server might come with one of the following hot-swap hard disk drive and backplane configurations:

• Five to eight 3.5-inch hot-swap SATA or SAS hard disk drives with two backplanes

• Up to four 3.5-inch hot-swap SATA or SAS hard disk drives with one backplane

• Up to eight 2.5-inch hot-swap SAS hard disk drives with one backplane

Chapter 3

.

Product overview

31

Summary of Contents for 70AL































































































































































































Reviews:

No comments