manualshive.com logo in svg

Lenovo 6431, Hardware Maintenance Manual

Share
Download
Lenovo 6431 Hardware Maintenance Manual Download Page 94

8. Set any jumpers or switches on the drive according to the documentation that

comes with the drive.

9. Remove the drive retainer clip from the side of the drive cage of bays 1 or 2.

Slide the drive retainer clip to the right to remove it from the drive cage; then,
snap the drive retainer clip into the screw holes on the side of the drive.

1

EMC shield

3

Tape drive

2

Filler panel

3

Drive retainer clip

10. Push the drive into the bay.

Note:

A tape drive can be installed in bay 1 or bay 2

11. Connect one end of the applicable signal cable into the rear of the drive and

make sure that the other end of this cable is connected into the applicable
connector on the system board.

12. Route the signal cable so that it does not block the airflow to the rear of the

drives or over the microprocessor and dual inline memory modules (DIMMs).

13. If you have another drive to install or remove, do so now.

14. Connect the power cable to the rear of the drive. The connectors are keyed

and can be inserted only one way.

Removing a hot-swap hard disk drive

This procedure applies only to server models that have hot-swap hard disk drives.

Attention:

To maintain proper system cooling, do not operate the server for more

than 10 minutes without either a drive or a filler panel installed in each drive bay.

To remove a hot-swap hard disk drive, complete the following steps:

76

ThinkServer TS100 Types 6431, 6432, 6433, and 6434: Hardware Maintenance Manual

Summary of Contents for 6431





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands