manualshive.com logo in svg

Lenovo 6431, Hardware Maintenance Manual

Share
Download
Lenovo 6431 Hardware Maintenance Manual Download Page 88

the adapter with the expansion slot guides; then, press the adapter firmly into
the expansion slot. For a full-length adapter, make sure that the front edge of
the adapter is correctly seated in the correct slot in the front adapter-retention
bracket.

1

Rear adapter retention bracket

4

Left side of the Front adapter
retention bracket

2

Expansion-slot screw

5

Right side of the Front adapter
retention bracket

3

Adapter

6. Install an expansion-slot screw at the rear of the adapter.

7. If you are installing a full-length adapter, press on the release lever on the right

side of the front adapter-retention bracket to release the retaining tab on the
left side of the bracket.

8. Connect required cables to the adapter. Route cables so that they do not block

the flow of air from the fans.

9. Install and lock the side cover (see “Installing the side cover” on page 63).

10. Reconnect the external cables and power cords; then, turn on the attached

devices and turn on the server.

70

ThinkServer TS100 Types 6431, 6432, 6433, and 6434: Hardware Maintenance Manual

Summary of Contents for 6431





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands