Lenovo 6431 Hardware Maintenance Manual Download Page 142

Page: 142 / 284

System board
mounting screws
(8 places)

Fan-sink mounting
bracket slots

10. Slide the system board toward the front of the server to disengage the tabs on

the fan sink mounting bracket from the slots on the bottom of the chassis;
then, carefully lift the system board out of the server.

11. Remove the four screws that secure the fan sink retention module

and fan

sink mounting bracket

to the system board; then, set the fan sink retention

module, fan sink mounting bracket, and screws aside for use later.

Note:

Make sure that you observe the orientation of the fan sink retention

module before you move it so that when you reinstall it, you install it in the
same orientation.

124

ThinkServer TS100 Types 6431, 6432, 6433, and 6434: Hardware Maintenance Manual

Summary of Contents for 6431





























































































































































































































































































Search results

Summary of Contents for 6431

Reviews:

Brands by name

Popular brands

Lenovo 6431, Hardware Maintenance Manual

Search results

Summary of Contents for 6431

Reviews:

Brands by name

Popular brands