background image

06/04

504,628M

*2P0604*

*P504628M*

Page 1

®

2004 Lennox Industries Inc.

Dallas, Texas, USA

WARNING

This product contain fiberglass wool.

Disturbing the insulation during installation, main-
tenance, or repair will expose you to fiberglass wool
dust. Breathing this may cause lung cancer. (Fiber-
glass wool is known to the State of California to
cause cancer.)

Fiberglass wool may also cause respiratory, skin,
and eye irritation.

To reduce exposure to this substance or for further
information, consult material safety data sheets
available from address shown below, or contact
your supervisor.

Lennox Industries Inc.
P.O. Box 799900
Dallas, TX 75379−9900

INSTALLATION
INSTRUCTIONS

OHR23 Series Units

OIL UNITS

504,628M
38152A061
06/04
Supersedes 4/02

Table of Contents

Elite Series Oil Furnace

1

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Shipping and Packing List

1

. . . . . . . . . . . . . . . . . . . . . . . . 

Unit Dimensions

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

OHR23 Unit Parts Arrangement

3

. . . . . . . . . . . . . . . . . . . 

Oil Burner Parts Arrangement

3

. . . . . . . . . . . . . . . . . . . . . 

Requirements

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Supply & Return Air Plenums

5

. . . . . . . . . . . . . . . . . . . . . 

Optional Filter Kit

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Initial Unit Adjustments 

6

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Venting

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Combustion and Ventilation Air

8

. . . . . . . . . . . . . . . . . . . . 

Flue Connections

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Oil Supply Lines Sizing 

12

. . . . . . . . . . . . . . . . . . . . . . . . . 

Oil Supply Line & Filter Connections

13

. . . . . . . . . . . . . . 

Leak Check

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Electrical Wiring

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Unit Start−Up & Adjustments

15

. . . . . . . . . . . . . . . . . . . . . 

Service

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Start−Up & Performance Checklist

17

. . . . . . . . . . . . . . . . 

Troubleshooting

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Elite

®

 Series Oil Furnace 

These instructions are intended as a general guide and do
not supersede local codes in any way. Only qualified tech-
nicians can install and service the Lennox Elite

®

 Series

OHR23 oil furnaces. In Canada, refer to CSA B139 for rec-
ommended installation procedures. Consult authorities
who have jurisdiction before installation.

WARNING

Improper installation, adjustment, alteration, ser-
vice or maintenance can cause personal injury, loss
of life, or damage to property.

Installation and service must be performed by a
qualified installer or service agency.

Shipping & Packing List 

 1− Assembled oil furnace
 1− Draft control

Check the components for shipping damage. If you find
any damage, immediately contact the last carrier.

CAUTION

Never burn garbage or paper in the heating system.
Never leave papers near or around the unit.

Do not store or use gasoline or other flammable va-
pors and liquids in the vicinity of this or any other
appliance.

When venting this appliance, keep vent terminal
free of snow, ice and debris.

Litho U.S.A.

Summary of Contents for OHR23-105

























Reviews: