PRIMARY CABINET COMPONENT INFORMATION
HIGH VOLTAGE POWER SUPPLY
The high voltage power supply is located in the bottom of the machine on the left hand side. inside of the power
box are the step down transformers, ballast for the lights,
filter and surge suppressor. The starters for
the three fluorescent lights are located on the front of the power supply box. There are four (4) circuit breakers
located on the front of the power box. The left 3 amp circuit breaker on the of the box is for the control board,
changer and validator if installed. The next circuit breaker to the right is the 12 AMP breaker for the 24 volts
for the carousel motor. The next circuit breaker to the right is the 2 amp breaker for the fluorescent lights and
the final circuit breaker to the right is the main 15 amp breaker for the entire machine. To the right of the circuit
breakers is the main power switch for the entire machine.
TRAY REMOVAL
NOTE: It is important to remember that the top tray (A row) in this machine will not interchange with any other
tray in this machine.
To remove a tray lift up slightly on the tray front while pulling the tray out to the loading position. Disconnect
the tray harness from the main motor distribution board. Set the tray harness on top of the tray. Pick up on
the front of the tray lifting the tray upward at 45 angle and outward. Grasp the tray at the front and the rear
and place it on a work surface.
To replace, reverse the operation. Grasp the tray, set the rear of the tray on the rails while holding the front
of
the tray at a
angle upward. Slide the tray in until stop on the bottom of the tray clears the front cross
rail. Then lower the front of the tray while sliding it in until it comes to the stop. Feed the tray harness around
and plug it into the main motor harness assembly.
Summary of Contents for Combo Series
