Leguan 135 NEO Operator'S And Service Manual Download Page 16

Page: 16 / 66

CONTROLS AND SWITCHES

Control devices on the platform

The platform’s controls and ind

icators on the control panel may be slightly different in different

models. Indicators and switches that are marked as optional are not installed on all models.

Figure 7 Platform control panel

Lowering button

Emergency stop switch

Horn / platform work lights (option)

Back to work position / Home -
Switch

Platform tilt enabler button

Platform rotation

Telescope in/out buttons

Joystick

Platform overload indicator

10.

Outreach control indicator

11.

Fault light

12.

Boom centre position indicator

13.

Boom transport position indicator

14.

Low fuel indicator

15.

Inclination sensor indicator

16.

Outrigger switches (manual)

17.

Automatic levelling switches

18.

Automatic levelling indication light
(light blinks) / boom use allowed
(light on)

19.

Combustion engine / electric motor
start/stop switch

20.

Automatic start / stop function
indicator light

21.

Speed selection / manual choke
switch

Summary of Contents for 135 NEO



































































Search results

Summary of Contents for 135 NEO

Reviews:

Related manuals for 135 NEO

Brands by name

Popular brands

Leguan 135 NEO, Operator'S And Service Manual

Search results

Summary of Contents for 135 NEO

Reviews:

Related manuals for 135 NEO

Brands by name

Popular brands