LEGRAND 5 735 04 Technical Data Manual Download Page 38

Page: 38 / 38

38/38

CONTENTS

Cat. No(s).: 5 735 04/05

5 735 12/13

KNX

Arteor 4 and 6 touches glass controls

Technical data sheet: S000090563EN-2

Updated: 07/06/2016

Created : 27/07/2015

11. COMMUNICATION OBJECTS DESCRIPTION (continued)

11.5 LED intensity update flowchart

The leds intensity changings are perfomed when :

- Is received an object of : Standby, Eco mode, Normal mode, Eco/Normal, Alarm

- Is pressed a push-button.

After Standby or Alarm mode the level is set to the previous level (Normal/Eco).

Standby mode is disables if any button is pressed.

11.6 No configuration status and reset procedure

Product not yet configured

The product has no physical address and no group addresses associated.

The leds change colors randomly every 200ms.

Reset procedure

All leds become

RED and fixed

Keep Prog/Reset

PB pressed for 10s

Short press PB

Prog/reset PB

During reset all

leds are RED

and fast blinking

Short press

Nota : when in programming mode (RED and fixed leds) there are 30min before timing out.

Leds intensity update

Yes

Normal

Eco

Standby

Alarm?

Mode?

Set leds intensity

to the chosen

Normal level

Set leds intensity

to the chosen

Eco level

Set leds intensity

to OFF

Set leds intensity

to100%

Request for leds intensity update

Summary of Contents for 5 735 04







































Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands

LEGRAND 5 735 04, Technical Data Manual

Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands