LEGRAND 5 735 04 Technical Data Manual Download Page 10

Page: 10 / 38

10/38

CONTENTS

Cat. No(s).: 5 735 04/05

5 735 12/13

KNX

Arteor 4 and 6 touches glass controls

Technical data sheet: S000090563EN-2

Updated: 07/06/2016

Created : 27/07/2015

11. COMMUNICATION OBJECTS DESCRIPTION (continued)

Parameters

These parameters determine the behaviour of the led after a push when

the “context info is used”.

Setting

Context information color ( if Feed back time ContextInfo is used)

Green (Vert)

Blue (Bleu)

White (Blanc)

Orange

Gold (Or)

Yellow (Jaune)

Turquoise

Cyan

Light blue (Bleu)

Violet

Pink (Rose)

Purple (Pourpre)

11.1.6 Long push configuration

This parameter determines the minimum time for detecting a long push action.

Long push action min.

0.5 second

1 second

2 seconds

3 seconds

4 seconds

5 seconds

10 seconds

11.1.7 Set maximum intensity after push during

If selected, after a push, the intensity of the led is raised to 100% during the set time. Return to the initial value at the end of time.

Set maximum intensity after

push during :

Not Used

500 ms

1 second

2 seconds

5 seconds

10 seconds

30 seconds

1 minute

1 min. 30s

2 min.

10 min.

15 min.

30 min.

45 min

1 h

1 h 30

11.1.8 Led behavior on Disable status

Determine the behaviour of leds when the commands receive disable telegram.

Summary of Contents for 5 735 04







































Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands

LEGRAND 5 735 04, Technical Data Manual

Search results

Summary of Contents for 5 735 04

Reviews:

Related manuals for 5 735 04

Brands by name

Popular brands