manualshive.com logo in svg

LeCroy AP034, Instruction Manual

Share
Download
LeCroy AP034 Instruction Manual Download Page 74

²

ISSUED: January 2000

AP034-OM-E Rev D

$3$FWLYH3UREH

COMPLIANCE AND CERTIFICATIONS

EC Declaration of Conformity:

Conforms to EMC Directive 89/335/EEC for electromagnetic
emission and immunity requirements.

EN 55011:1997:

The probe has been tested to verify compliance with this
standard, Class B for Conducted and Radiated Emissions.

NE 50082-1:1997:

The probe has been tested to verify compliance with this
standard for ESD, Radiated Immunity, EFT/Burst Immunity, Fast
Surge Immunity, Conducted Immunity, and Voltage Sags &
Interruptions. The line-related tests were performed with a model
ADPPS Probe Power Supply.

Conforms to Low Voltage Directive 73/23/EEC for product safety.

The probe has been designed to comply with EN 61010-1
Installation Category I, 42.4 V, Pollution Degree 1.

OPERATOR SAFETY

The probe is intended to be used only with instruments that are
connected to earth ground through the input BNC connector.
When you are using a ADPPS Power Supply Adapter, make sure
that the adapter is connected to a BNC connector that is
grounded by the test instrument before connecting the probe
inputs to the test circuit.

Do not use in wet or explosive atmospheres. Remove any
contamination from the probe housing before connecting the
probe inputs to any circuit. Make sure that the surface of the
probe head is completely dry before connecting the inputs.

The use of the probe and/or the instrument it is connected to in a
manner other than specified may impair the protection
mechanisms.

Do not use the probe if any part is damaged. All maintenance
should be referred to qualified service personnel.

Summary of Contents for AP034













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands