manualshive.com logo in svg

LeCroy AP034, Instruction Manual

Share
Download
LeCroy AP034 Instruction Manual Download Page 66

²

ISSUED: January 2000

AP034-OM-E Rev D

$3$FWLYH3UREH

5. Adjust 

Attenuator CMRR (capacitor C18A) for minimum

amplitude shift of the displayed waveform at the trigger
point in time. See Figure 10 for adjustment location.

6.  Leave the setup connected for the next step.

H. Assemble Probe and Amplifier

1.  Carefully slide the large probe tip cover over the probe tip,

being careful to engage the input pins.

2.  Snap the small probe cover with the threaded brass insert

onto the bottom of the probe. Engage the probe cable
strain relief into the mating area of the cover. Carefully
dress the wires entering the cable to clear the area above
the brass insert.

3.  Place the lip on the large end of the remaining cover under

the mating surface near the probe tip. Gently press the
cover into place. If the cover appears not to close
completely, remove it and again check for adequate
clearance between the brass insert and the cable wires.

4. Replace 

the 

5

/

64

 in. Allen cap screw and tighten.

5.  Hold the Logic Board/Amplifier Board assembly in one

hand with the Logic board facing up. Hold the ProBus
Interface housing in the other hand with the control side
(side with holes for the buttons) facing up.

6.  Align the edges of the Amplifier Board with the slots in the

center of the inside of the housing. (The amplifier board is
the thicker circuit board and has the BNC connector
soldered to it.) Slide the boards into the housing, being
careful to align the screw holes in the end cover with the
corresponding channels in the corners of the housing.

7.  Insert and tighten the two screws that secure the end panel

to the ProBus interface housing. Avoid overtightening the
screws because the cover may warp.

8.  Replace the four push button caps, pressing each fully to

seat the cap on the button shaft.

Summary of Contents for AP034













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands