LCN 4110 Series Peel-N-Stick Product Manual Download Page 4

Page: 4 / 74

HINGE (PULL) SIDE
MOUNTING

MAXIMUM OPENING

Can be templated for 100°,

A = 5 15/16” (151 mm)
B = 11 15/16” (303 mm)

or 140°.

A = 4 3/16” (106 mm)
B = 10 3/16” (259 mm)

Hold-open points up to maximum
opening with hold-open arm.

Arm Clearance

above door.

Regular arm requires C =
1 1/16” (27 mm).
Hold-open arm requires C =
1 3/8” (35 mm).
Fusible link arm requires C =
1 5/8” (41 mm).

LCN

4010 SERIES

Butt Hinges

should not exceed 5” (127 mm) in width.

Auxiliary Stop

is recommended at hold-open point or where a door

cannot swing 140°.

Reveal

should not exceed 3/4” (19 mm). Fusible link arm should not

exceed 1/8” (3 mm).

Top Rail

less than 3

” (95 mm) requires PLATE, 4010-18.

Plate requires 2” (51 mm) minimum.

Clearance

of 2 1/4” (57 mm) behind door required for 90° installation.

Delayed Action

Add suffix “DEL” to selected cylinder.

Not available with 4016 cylinder.

Delays closing from maximum opening to approximately 70°.

Delay time adjustable up to approximately 1 minute.

Options

Size 6 or non-sized cylinder.
Delayed action cylinder.
Hold-open or fusible link arm.
Metal cover.

Special Templates

Customized installation templates
or products may be available to
solve unusual applications.
Contact LCN for assistance.

LCN CLOSERS
121 W. RAILROAD AVE.
P.O. BOX 100
PRINCETON, IL, USA 61356-0100

PHONE 800-526-2400
FAX 800-248-1460
www.lcn.ingersollrand.com
3/10

Summary of Contents for 4110 Series Peel-N-Stick











































































Search results

Summary of Contents for 4110 Series Peel-N-Stick

Reviews:

Related manuals for 4110 Series Peel-N-Stick

Brands by name

Popular brands

LCN 4110 Series Peel-N-Stick, Product Manual

Search results

Summary of Contents for 4110 Series Peel-N-Stick

Reviews:

Related manuals for 4110 Series Peel-N-Stick

Brands by name

Popular brands