LAWO A mic8 User Manual Download Page 22

Page: 22 / 66

A__mic8 / A__digital8 User Guide

Version: 10.0.0/4

22/66

11. The RAVENNA Web UI

11. The RAVENNA Web UI

This chapter describes the RAVENNA Web UI, otherwise known as the "Butler" interface.

11.1

Applications

For A__mic8 or A__digital8 devices, the RAVENNA Web UI is used for three main tasks:

To check and, if necessary, update the device firmware.

To edit the device's sync source and sample rate.

To create and manage the TX and RX streams, including SMPTE 2022-7 compatible streams.

Note that the latest settings are stored locally on the device, and are re-instated following a power cycle or reboot.

Any settings changed from the RAVENNA Web UI can be backed up (and restored) using the

Backup & Restore

Config

tool. This is ideal if you need to exchange a device.

11.2

Prerequisites

To run the RAVENNA Web UI, your computer

MUST

meet or exceed the following requirements:

Processor:

Pentium 166 or higher

RAM:

64 MB

Network Interface Card

: operating at 100 or 1000 Base-T

Screen Resolution:

>= 1024 x 786

Web Browser

: Microsoft Internet Explorer, Mozilla Firefox, Apple Safari or Google Chrome. Please

install the latest version of the browser for best performance.

11.3

Opening the Home page

To open a RAVENNA Web UI connection:

Connect a service computer and configure its TCP/IP settings as described

earlier

Open the

Landing page

, select

RAVENNA/AES67

and then click on the graphical preview.

The RAVENNA

Home

page should appear.

Summary of Contents for A mic8



































































Search results

Summary of Contents for A mic8

Reviews:

Related manuals for A mic8

Brands by name

Popular brands

LAWO A mic8, User Manual

Search results

Summary of Contents for A mic8

Reviews:

Related manuals for A mic8

Brands by name

Popular brands