![background image](http://html2.mh-extra.com/html/lawn-king/m85/m85_operating-instructions-manual_3982272019.webp)
11
n
GEARBOX (Fig. 11)
: Check the gearbox oil level every 60 hours of work. Disassemble the right wheel and, keeping the unit on horizontal
position, unscrew the cap (1) placed on the side.
The oil level must be at the lower level of the filling hole. In case it is not filled in , please add SAE 80 oil type.
ATTENTION! The used oil must not be drained into the sewer system or waterworks. In order to prevent any pollution to the water-table. Most garages
have used oil deposits, or use the authorized deposits according to your local authority regulations.
n
TRANSMISSION SCYTHING BAR (Fig. 12)
there are 2 greasing point (1-2) . Important : after every use of the motor mower , please
clean and grease the scything bar and all motion parts/mechanisms.
n
ENGINE SERVICING
( please read the specific part). The motor mower is delivered equipped with a 4 stroke engine , NO OIL is included. Please
fill the tank in up to the shown level ( capacity about 0,5 kg.). Referring to the oil/viscosity type, please follow the engine producer instructions.
n
SERVICE - GARAGING :
the motor mower is undoubted one of the most used agricultural equipment and need a good and frequent
servicing. We recommend you to clean the machine very deeply after every use. Keep attention that all the nuts , screws and bolts are tightened in
order to guarantee a good machine working on safety conditions. Leave the machine to cool before garaging anyhow don’t room it if the tank contains
still contains some fuel as the vapours could reach some blazes or sparks. To lower the fire danger , keep the engine , the silencer and the fuel area
free from leaves, grass or greasy substances.
If the machine is not used for long periods it is essential to protect the blade and the bar using some anticorrosive and antioxidant materials. The
presence of impurities or foreign bodies on the meadow, damages the teeth sharpening of the scything bar. It is useful to sharpen the blade and check
the teeth integrity every 4-6 hours of use. Only if you keep a good sharpening teeth level you can obtain the best grass cut.
n
BLADE SHARPENING (Fig. 13) :
according to the frequency and the type of use , the cutting sections have to be sharpened about every
10 hours working. To obtain a perfect sharpening you need to use and electric sharpening machine (15.000/20.000 turns/minute) , grinding-headed
with a diameter 25 mm and length 35 mm. The blade has to be sharpened from the internal part of the rod to tip.end section using the head grinding.
The blade sections have to be sharpened in a 25° deg. angle.
n
DESCRIPTION (Fig. 15)
1) Start-Stop operating lever - 2) Drive operating lever - 3) Cutter bar clutching control lever - 4) Engine - 5) Cutter
bar. 6) Cable-guide Bracket – 7) Cowling.
n
TECHNICAL DETAILS
Track: 430 mm - Length of cutter bar: 660/870 mm - Total length: 1350 mm - Total height: 1050 mm - Tires: 2 tires
13x5.00-6 - Mass: 49/52 kg. MOTOR - Cooling: air cooling - Fuel tank: 0,75 Litre. Please consult the relative instruction manual for other technical
information and details about the engine.
n
NOISE AND VIBRATION LEVEL
Measured sound pressure level with En12733 Leq = 81,4 dB (A), with a uncertainty value K = ±1,1 dB
EN
Summary of Contents for M85
