![background image](http://html2.mh-extra.com/html/lawn-king/m85/m85_operating-instructions-manual_3982272017.webp)
9
n
ASSEMBLY OF THE THROTTLE CABLE ON ENGINE625 Series (Fig. 3)
Move the throttle lever (1) ,positioned on the
engine, on the stop position. Using the corresponding key, take off the screw (2) and protective covering clamp (4).
After that, put the throttle hand-lever (part. 1 fig.15), fixed to the handlebar , on the stop position and the “S” of the wire into the slot (3) which is marked
with the arrow on the engine leverage (1). Position the protective covering on the base of the clamp and tighten it using the screw (2).
n
ASSEMBLY OF THE FORWARD SPEED CABLE (Fig. 5 )
Driving wire is already connected with the belt-stretching spring (see
fig. 8). Connect it to the lever (6) on handlebar as follows: make the cable (3) to pass into the ring of the handlebar support and the terminal part (1)
into the lever hole (2). First , give a slight pull to the covering , then make the cable to pass into the nib cut-hole (5). Leaving the adjusting nuts (4) as
shown in the picture.
n
ASSEMBLY CABLE FOR BAR CONNECTION (Fig. 4 -7)
the cable adjustment is already linked to the black lever to be used to
connect the accessories placed under the frame. You need to make the cable to pass into the nib placed on the side of the frame ( fig. 15 part. 6).
Bring it to the handlebar and make the terminal (1) to pass first into the nib hole (2) then into the red levers one ( for accessories connection) as shown
in the picture. N.B.: we suggest you to perform such assembly before fixing the scything-set device to the motor mower.
Fig. 7) How to operate the unit – unit + fitting :
- disconnect the safety lever (3) rotating it to the top then lower the fitting insertion lever (4).
- to insert the forward gear or the reverse you need to pull the clutch lever (1).
- to move with the engaged fitting you need the levers (1) and (4) are operated at the same time.
When releasing each lever (1) and (4) you can immediately stop the function which was previously engaged.
n
SCYTHING BLADE ASSEMBLY (Fig. 14 - 14A)
: ATTENTION! before handling the cutting bar please assemble the protection part
you can find inside the packaging box . For protection safety purposes, please always wear a pair of hardy gauntlets. To make the assembly of the
scything blade we recommend you to do it on a work bench.
Fig. 14) In the accessories envelope you can find a spacer-lock (5) which has to be positioned on the bar driving plate (6). Bring the blade in the
correct position and put the pin (7) into the spacer-lock (5).
Fig. 14A) The scything blade (1) has to be screwed to the bar support (2) using 4 screws M8 x 20 (3) and 4 nuts (4) you can find the parts in the
accessories envelope.
GO ON WITH THE ASSEMBLY OF THE CUTTING BAR SET ON THE MOTOR MOWER (Fig. 6 - 6a - 6b - 6c)
The motor mower has a coupling for
quick and easy attachment of the cutter bar and accessory snow-blade.
Fig. 6) The motor should be turned off and the machine positioned on a flat surface. Insert the cutter bar pin (1) into its seating (2).
Fig. 6a) Install the belt (3) in its pulley (4) making attention to stay inside the belt drives (5).
Fig .6b) Attach the springs (1), supplied in the accessories envelope, to their hooks (2), then to the holes (3).
Fig. 6c) Replace the cowling (part.7 fig.15) with its entering pin (5).
Tighten firmly the nut (7) with its washer (6) on the cowling.
For models equipped with 87 cm. cutting bar please complete the assembly adding the missing sliding part ( part. 2 – fig. 10) you can find in the
accessories envelope. Please refer also to chapter : “cutter bar height adjustment”.
EN
Summary of Contents for M85
