Lauda LRZ 926 Operation Manual Download Page 36 | Manualshive

Page: 36 / 44

Lauda LRZ 926 Operation Manual Download Page 36

9 Faults

If a fault occurs, the interface distinguishes between different message types,

e.g. alarms, errors and warnings. The procedure for rectifying a fault depends

on the device. Follow the corresponding instructions in the operating manual

accompanying the constant temperature equipment.

If you are unable to rectify a fault, please contact LAUDA Service,

see

Chapter 1.6 “Contact LAUDA” on page 7

.

9.1

Alarm

The RS 232/485 interface recognizes the following alarm messages.

Table 27: RS 232/485 alarm messages

Code

Meaning

11

Triggers when the command with ID 15 (actual value external temperature) has not been received

for several seconds while the system is regulating to the "external serial" control variable.

22

Disconnection detected.

There was no communication for a period longer than the preset timeout.

9.2 Error

The RS 232/485 interface recognizes the following error messages.

Table 28: RS 232/485 error messages

Code *

Meaning

501 – 504, 507, 508 Interface module hardware faulty. Contact the LAUDA department.
505

Internal 24 V voltage of the interface module is too low.

506

Internal 24 V voltage of the interface module is too high.

V1

Interface module LRZ 926

36 / 43

«
...
34
35
36
37
38
...
»

Summary of Contents for LRZ 926













































Reviews:

No comments