manualshive.com logo in svg

Laser Dollhouse Designs Stansfield Victorian Dollhouse, Assembly Instructions Manual

Share
Download
Laser Dollhouse Designs Stansfield Victorian Dollhouse Assembly Instructions Manual Download Page 8

Pre-Assembly Parts

French Door

Figure 1

Figure 3

Figure 2

Step 1. Locate the package with the French door, remove items. You should have:
2-Door frames and 2 exterior lattice frame.   
1-Door stop
1-outer frame rail
1-interior frame rail
1-upper cross frame rail and 1 lower cross frame rail with holes for door stop.
1-Frame for interior (not pictured) 
1-Frame for exterior  ( 

1:48 scale has standard frame

). 

2- Gingerbread head door frames. 

( Not in 1:48 )

2- wall corbels 

( Not in 1:48 )

2-glass
You will need 220 grit sand paper for the assemble for cleaning doors.. 

Step 2. Locate main exterior frame, corbels, and head door frames. Next glue the 

Corbels into the main frame as seen in figure 2. Next using wood glue!! Glue the 
two head door frames evenly onto the main exterior frame. Figure 3. Make sure 
that the frames are evenly glued and aligned in all three layers. 

DO NOT USE 

SUPER GLUE!!! 

Summary of Contents for Stansfield Victorian Dollhouse



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands